Car Key Button Repair
A broken car key button can be frustrating. You might need to call an emergency locksmith service 24 hours a day to assistance or purchase a replacement remote.
But, you may be in a position to save money by repairing an old key fob rather than replacing it. This is particularly true if the problem is caused by a worn switch or faulty contact.
Battery
If the buttons on your key fob aren't responding to pressing, that could be a sign that the battery is dying or at the end of its lifespan. It's simple to replace the battery on your own instead of paying locksmiths or dealers.
First, locate the battery compartment. This is usually found on the backside of the key fob and may be hidden behind an open cover that slides out or an access point that opens when you press a button. After the compartment is opened, look for the small button-cell battery. It's usually the shape of an ordinary coin and is has a plus and the minus symbol. Remove the battery from the old one and put a brand new one in its place, making sure that the plus and minus marks are properly aligned.
Once the battery is in place close the compartment and snap the two parts of the key fob. Before closing the door ensure that you align and snap the components into the correct position. Press any of the buttons to confirm that they work properly.
If your remote keyfob still does not work after replacing the battery, it could be other issues that require a different kind of repair. Dropping the fob into a puddle can cause it to cease functioning. Or, it could be suffering from an electrical issue within the device or may need to be deprogrammed by a dealer or locksmith. See if you can find out if the issue is with your key fob applying these other typical methods for troubleshooting your car.
Switches
Based on the year and the make, there are different kinds of switches available on the car keyfob. The older style keys have a chip that is visible in the case. The modern keys function by sending signals to your car. The keys' buttons can be worn out or damaged through regular use, irrespective of the model. The result is they become difficult to press or even unresponsive. If you try to press the button too hard the button, it could cause damage and potentially stop the key from being able to start your vehicle in the future.
If you can't get your key to work Try changing the batteries. If this doesn't work, you might need to clean your key fob or re-adjust the switches. Since these tiny electronic switches are constantly being tossed around and tangled, they are more likely to fail than the larger parts of your key.
The switches have a rubbery feeling and are coated with a film that conducts electricity. The film is prone to be worn away over time. Luckily, they're also tiny and cheap to replace. They are soldered onto the circuit board, so you need to carefully remove the old ones without causing any damage to anything else. You can then solder new ones into and then reassemble your fob.
One way to prevent your car key fob from getting damaged is to avoid using it for longer than a couple of hours at a time and to avoid leaving it in visible locations in areas where it is visible. If you don't use your key, store it in a secure location.
If the problem persists after you have cleaned your key fob, replaced the battery and attempted to clean it, you may need to talk to an expert locksmith. A professional can check the frequency of your key to determine if it's still able to communicate with your vehicle. They can also open and replace micro switches, change cases and more.
Outer Case
A key fob spends a lot of time jostled around, and when the buttons aren't able to move up and down within the case, they may become stuck or break. If cleaning the case using rubbing alcohol and a cotton swab doesn't work, it might be necessary to remove the case. If the contact points where the buttons touch don't fit well or are worn out, adjusting them might be the only option to fix the problem.
Some keys use buttons made of rubber that wear away over time. Rubber buttons can become hard to press because they stretch, and nails can cut them. This can cause the key to fail and in this instance it's time for an entirely new case or buttons. This repair involves disassembling the remote, then locating the buttons on the circuit board, heating up the solder before carefully taking them off. New buttons are then attached to the circuit board. The case can be reassembled, and the horseshoe key blade can be inserted. remote key fob repair near me should be a close fit into the case to prevent them from falling out.
Inner Case
Since your key fob is likely to be tossed around and could sometimes be accidentally pressed, the buttons inside can get damaged or stuck over time. With the help of metallic tape and a hole punch you can usually solve this issue in the event that your vehicle is not at home and the key fob isn't working, allowing you to unlock the doors, but not to start the engine. This quick fix could allow you to safely make it back to your vehicle and finish your trip.
